manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации, Страница: 164 / 226

Поделиться
Скачать
Siemens Synco700 RMK770 Скачать руководство пользователя страница 164

164/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

10 Heating circuit control 

01.03.2005 

•

 When 

all 3

 temperatures lie 1 °C 

below

 the Economy heating limit, heat will be re-

leased in Economy   and Protection   mode 

•

 When 

1 of the 3

 temperatures lies 

above

 the Economy heating limit, delivery of heat 

will be locked  

HDCmf

HDEco

TOact

TOStrDmp.

TOeff

31

31

D

3

0

Cmf
heating
limit

Eco
heating
limit

 

 

  Main menu > Settings > Heating circuit > Space heating 

Operating line 

Range 

Factory setting 

Comfort heating limit 

--- (none) / –5…25 °C 

17 °C 

Economy heating limit 

--- (none) / –5…25 °C 

5 °C 

The following applies:  

•

  If the Comfort heating limit is set to --- (none), there is a heating limit only in Econ-

omy   and Protection   mode. There will be no changeover to summer operation 

•

  If the Economy heating limit is set to --- (none), the Comfort heating limit acts in 

Economy 

 

and Protection   mode 

 
For operation in combination with the ventilation controller, summer / winter operation 
changeover is used as an overriding function. 
When the attenuated outside temperature exceeds the Comfort heating limit, a change 
to summer operation will be made; this also applies to “Continuously Comfort

  ”

. 

10.7  Mixing valve control 

10.7.1 Control 

  

The flow temperature setpoint determined by weather-compensated heating circuit 
control produces the effective setpoint for mixing valve control while giving considera-
tion to load control.  
 
Mixing valve control can be accomplished with a 3-position mixing valve or a mixing 
valve using DC 0…10 V control. The type of actuator is selected in the extra configura-
tion. 
The following mixing valve settings apply to both the 3-position mixing valve and the 
DC 0…10 V actuator: 

  Main menu > Commissioning > Settings > … 

or

  

  Main menu > Settings > Heating circuit > Controller 

Operating line 

Range 

Factory setting 

Actuator running time 

1…600 s 

120 s 

P-band Xp 

1…100 K 

48 K 

Integral action time Tn 

0…600 s 

10 s 

 

For more detailed information about mixing valve control and its setting aids, refer to 
section 5.7 “Mixing valve control”.  

Economy heating limit 

Settings 

Summer / winter operation 
(information for ventilation) 

 Setpoint 

3-position / DC 0…10 V 
actuator 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов