Siemens Synco700 RMK770 Скачать руководство пользователя страница 4

Страница: 4 / 226

4/226

Building Technologies

Boiler Sequence Controller RMK770

CE1P3132en

HVAC Products

Contents

01.03.2005

3.9

Device information .........................................................................................48

3.10

Leaving the password level............................................................................48

3.11

Marking changes............................................................................................48

3.12

Plant types and default terminal assignments ...............................................49

General settings.............................................................................................53

4.1

Time of day and date .....................................................................................53

4.1.1

Operating principle.........................................................................................53

4.1.2

Communication ..............................................................................................53

4.1.3

Error handling ................................................................................................54

4.2

Selecting the language ..................................................................................55

4.3

Selecting the unit of temperature ...................................................................55

4.4

Contrast on the operator unit’s display ..........................................................55

4.5

Text entry .......................................................................................................56

4.5.1

Device name and file name ...........................................................................56

4.5.2

Aggregate names...........................................................................................56

4.5.3

Text of fault inputs..........................................................................................56

4.5.4

Electronic business card ................................................................................56

General functions, fundamentals ...................................................................58

5.1

Time switch ....................................................................................................58

5.1.1

Communication ..............................................................................................58

5.1.2

Time switch for external controllers on the bus..............................................58

5.1.3

Entering the 24-hour program for space heating ...........................................59

5.1.4

Error handling ................................................................................................60

5.2

Holidays/special days ....................................................................................60

5.2.1

Communication ..............................................................................................60

5.2.2

Holidays .........................................................................................................61

5.2.3

Special days...................................................................................................61

5.2.4

Calendar entry ...............................................................................................62

5.2.5

Control inputs for holidays and special days..................................................62

5.2.6

Error handling ................................................................................................63

5.3

Frost protection for the plant ..........................................................................63

5.4

Pump overrun and mixing valve overrun .......................................................64

5.5

Pump kick and valve kick...............................................................................64

5.6

Heat demand and load control.......................................................................65

5.6.1

Heat demand .................................................................................................65

5.6.2

Load control ...................................................................................................66

5.7

Mixing valve control .......................................................................................67

5.7.1

Control ...........................................................................................................67

5.7.2

Setting aids ....................................................................................................68

5.7.3

Control signal .................................................................................................70

5.8

Pump control and twin pumps........................................................................71

Содержание Synco700 RMK770



































































































































































































































Результаты поиска

Содержание Synco700 RMK770

Отзывы:

Похожие инструкции для Synco700 RMK770

Бренды по названию

Популярные бренды

Siemens Synco700 RMK770, Руководство по документации

Результаты поиска

Содержание Synco700 RMK770

Отзывы:

Похожие инструкции для Synco700 RMK770

Бренды по названию

Популярные бренды