Siemens Synco700 RMK770 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 226

Siemens Synco700 RMK770 Скачать руководство пользователя страница 33

33/226

Building Technologies

Boiler Sequence Controller RMK770

CE1P3132en

HVAC Products

3 Commissioning

01.03.2005

N.

Y1

Y

RM
K7

70

N.

Q4

Q

N.

Q

1

Q

N.

Q2

Q

N.

Q

3

Q

N.

Q5

Q

N.

Q

6

Q

N.

Q7

Q

aa

d
d
d
d

1

2

3

4

5

6

Auto

a

DC 0...10 V

d
d
d

1.
2.

d

a

d

a

d

d

d

Q
QQ

Y

a
d
d

d

N1

N2

N.

X7

x

N.X
8

x

N.

X6

x

N.X
5

x

N.

X3

x

N.X
4

x

N.

X2

x

N.X
1

x

a

Q

d
d

B

d

B

V

Q

a

0...10 V

Y

d

d
d
d

Q

d
d

B

d

B

V

Q

a

N.

Y2

Y

0...10 V

Y

0...10 V

Y

2)

1)

2)

2)

1)

3P

3P

3P

3P

3P

3P

N.

D

1

d

N.

D

2

d

1.
2.

d

a

d

a

d

d

d

Q
QQ

Y

a
d
d

Q

d
d

B

d

B

V

Q

a

0...10 V

Y

d

0...10 V

Y

2)

2)

1)

3P

3P

A7

.Q

1

Q

A7

.Q

2

Q

A7

.Q

3

QQ

A7

.Q

5

3P

3132Z15

A7

.X

3

x

A7

.X

4

x

A7

.X

2

x

A7

.X

1

x

RM
Z7

87

(1

)

B

oil

er s

equ

en

ce

m

ana

ge

r

Main flow

Main return

Bo

ile

r-

se

qu

en

ce

se

lect

ion

Release

Constant

DHW

Frost prot.

Consumer return

(Water shortage) 1

(Overpressure) 2

(Underpressure) 3

MBRT return

close

open

H

ea

t re

qu

is.

Bo

ile

r 1

Mo

du

lati

ng

Shutoff valve

Flue gas

Burner

Curr burner outp

Setpoint comp.

St

ag

e

Release

Flue gas mode

(Water shortage) 1

(Overpressure) 2

(Underpressure) 3

Individual operation

Burner

close

open

Boiler

Return

close

open

dig.

dig.

Autonom

Shutoff valve

Bo

ile

r-

pu

m

p

MB
RT

Ma

in

pu

m

p

M

ain

t b

oile

r

re

turn

te

m

p

Bo

ile

r 2

Mo

du

lati

ng

Shutoff valve

Flue gas

Burner

Curr burner outp

Setpoint comp.

St

ag

e

Release

Flue gas mode

(Water shortage) 1

(Overpressure) 2

(Underpressure) 3

Burner

close

open

Boiler

Return

close

open

Shutoff valve

Bo

ile

r-

pu

m

p

MB
RT

The configuration diagram shows all function blocks active in the plant type. These are
the following function blocks in this example:

•

Boiler sequence manager

•

Boiler 1

•

Boiler 2

The configuration diagram shows the inputs and outputs that are preconfigured.
If required, additional inputs and outputs (e.g. flue gas temperature sensor, burner
operation checkback signal) can be assigned to the free inputs and outputs in the extra
configuration.

Also, it is possible to see which extension modules are required. For plant type K5.2,
extension module RMZ787(1) is used as standard. This is shown on the “Basic configu-
ration” menu, operating line "Position 1".
If required, the output for the first or the second boiler pump can also be configured to
some other output. It is also possible to change the type of extension module.
On function block “Boiler sequence manager“, the main flow temperature sensor (N.X1)
and the main return temperature sensor (N.X2) are preconfigured.
This can be checked on

Extra configuration > Boiler sequence manager > Inputs

.

On function block “Boiler 1“, the boiler temperature sensor is configured to terminal
N.X3. The burner is preconfigured to outputs N.Q2 and N.Q3, the boiler pump to
A7.Q1, and the shutoff valve to the relay with changeover contact N.Q1.

For boiler 2 – analogously – N.X6 is preconfigured for the boiler temperature sensor,
N.Q5 and N.Q6 for the 2-stage burner, N.Q4 for the shutoff valve, and A7.Q2 for the
boiler pump.

This can be checked on

Extra configuration > Boiler 1 (

or

b

oiler 2

)

> Inputs

(or

o

utputs

).

It is possible to reconfigure or remove preconfigured inputs and outputs. If, for example,
the second burner stage is removed from boiler 1 (---in place of N.Q3), the burner of
boiler 1 becomes a 1-stage burner.

Several function blocks can be activated in the extra configuration.

Function blocks

Inputs and outputs

Extension modules

«
...
31
32
33
34
35
...
»

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов