manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации


Поделиться
Скачать
background image

183/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

12 Function block faults 

01.03.2005 

Following can be set for each fault status message: 

  

Main menu > Commissioning > Settings > Faults > Fault input…  

Operating line 

Range 

Factory setting 

Fault text  

Free text, max. 20 char-
acters 

Aux 1 

Fault status signal delay 

00.00…59.55 m.s  

00.05 m.s 

Fault acknowledgement 

None / Acknowledge / 
Acknowledge and reset 

None 

Fault priority 

Urgent / Not urgent 

Not urgent 

Impact of fault 

No stop / Stop 

Stop 

Limit value fault on 

0 / 1* 

1 

Limit value fault off 

0 / 1* 

0 

*  Depends on “Input identifier” 

 

These settings can only be made if the relevant input has previously been activated in 
the extra configuration. 
For more detailed information, refer to section 12.4 “Fault properties”. 
 
The text for the universal status inputs is predefined with Aux 1 through Aux 4. The 
texts can be adapted. 
 

Signal at the fault 

input

Fault status mes-

sage

3131

D

31

 

Signal delay 

 

 

The fault status signal delay is used to set the period of time a fault  
must be pending to be handled as such. 
 
Parameter setting “Stop“ at the universal fault inputs means that the entire boiler se-
quence will be shut down. 
 

Number Text 

Effect 

9001 

Aux 1 

Effect in accordance with the settings 

9002 

Aux 2 

Effect in accordance with the settings 

9003 

Aux 3 

Effect in accordance with the settings 

9004 

Aux 4 

Effect in accordance with the settings 

 
The digital status inputs cannot be monitored. We recommend to use wiring ensuring 
that the signal drops out when a fault is pending. 

12.7.2  Analog fault input with limit value supervision 

  

An analog input can be monitored for limit value crossings. 
An input that is already configured can also be monitored. For example, the main flow 
temperature sensor can be monitored to ensure that a maximum flow temperature will 
not be exceeded. 
 

Fault text  

Fault status 
signal delay 

Effect of fault 

Fault status messages 

Error handling 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco700 RMK770

ABB Relion 670 series Applications Manual preview
Relion 670 series
Бренд: ABB Страницы: 760
ABB 650 series Engineering Manual preview
650 series
Бренд: ABB Страницы: 128
D-Link DWC-2000 Cli Reference Manual preview
DWC-2000
Бренд: D-Link Страницы: 113
D-Link DWC-1000 Reference Manual preview
DWC-1000
Бренд: D-Link Страницы: 146
IBM 3708 End-User Reference preview
3708
Бренд: IBM Страницы: 144
Bang & Olufsen BeoSystem 4 How To Use Manual preview
BeoSystem 4
Бренд: Bang & Olufsen Страницы: 36
Mad Catz DVD 2 Owner'S Manual preview
DVD 2
Бренд: Mad Catz Страницы: 4
ZKTeco F6 Installation Manual preview
F6
Бренд: ZKTeco Страницы: 2
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Бренд: FASAR ELETTRONICA Страницы: 2
Faro Barcelona 33929 Installation Manual preview
33929
Бренд: Faro Barcelona Страницы: 8
Faro 33928 Installation Manual preview
33928
Бренд: Faro Страницы: 3
YASKAWA G7 Series Technical Manual preview
G7 Series
Бренд: YASKAWA Страницы: 456
GBD F4 Instructions For Installation Manual preview
F4
Бренд: GBD Страницы: 15
Lantronix xPico 200 Series Manual preview
xPico 200 Series
Бренд: Lantronix Страницы: 7
Lantronix xPico 110 Quick Start Manual preview
xPico 110
Бренд: Lantronix Страницы: 3
Lantronix EDS1100 Quick Start Manual preview
EDS1100
Бренд: Lantronix Страницы: 15
U-Prox MP LTE User Manual preview
MP LTE
Бренд: U-Prox Страницы: 3
U-Prox IP500 Installation And Programming Manual preview
IP500
Бренд: U-Prox Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды