manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации


Поделиться
Скачать
background image

102/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

7 Boiler temperature control 

01.03.2005 

7.2.1 Burner 

types 

 

By selecting the plant type, the type of burner is predefined for 2 boilers of the boiler 
sequence. 

•

  Kx.1: 1-stage burner 

•

  Kx.2: 2-stage burner 

•

  Kx.3: Modulating 3-position 

The relevant outputs are preconfigured. 
The outputs can be changed in the extra configuration. 
 
First burner stage or basic stage of a modulating burner. 
 
Second burner stage  
 
Configuration of a pair of terminals for a modulating 3-position burner.  
Available for selection are the remaining free terminal pairs (Q1/Q2, Q3/Q4, Q5/Q6) for 
the open and the close signal. Normally, special terminal pairs are required (RC unit for 
radio interference suppression; for more detailed information, refer to subsection 3.3.2 
“Terminal assignment and properties of outputs”). 
 
DC 0…10 V output for a modulating burner. 
 
DC 0…10 V output as a boiler temperature setpoint for an external boiler temperature 
controller. 
If no control of the burner is required, the DC 0…10 V output can also be used for set-
point compensation of a boiler. In that case, it is not the boiler temperature that is con-
trolled, but the boiler temperature setpoint is shifted as a function of the main flow tem-
perature. 

7.2.2 Boiler 

hydraulics 

 

The following pumps are usually present:  

•

  One boiler pump per boiler  

•

  The main pump for all boilers  

It is also possible to use a boiler pump as a mixing pump or a combination of mixing 
pump and main pump. 

 

A

B

T

31

3

2S

6

2

 

T

31

3

2

S

6

3

 

T

313

2S

64

T

 

 

T

31

3

2S

6

5

T

Boiler pump 

Boiler mixing 
pump 

Main pump 

Boiler mixing pump and 
main pump 

 

•

  Plant types K1.x and K2.x use 1 main pump 

•

  Plant type K3.x uses 1 main pump and 1 mixing pump  

•

  Plant types K4.x, K5.x and K6.x use 1 boiler pump 

 

By assigning an output to boiler pump A, a boiler pump is activated for the boiler. In 
terms of configuration, no difference is made between boiler pump and mixing pump. 
Optionally, a twin pump can be used in place of the boiler pump. In that case, in addi-
tion to boiler pump A, boiler pump B in the extra configuration must be assigned an 
output. 

Burner stage 1  

Burner stage 2 

Modulating 3-position 

Modulating burner mod 

Setpoint compensation 

Definition of pumps 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco700 RMK770

Canon BU-51H Remote Control Manual preview
BU-51H
Бренд: Canon Страницы: 2
jbc DI Series Manual preview
DI Series
Бренд: jbc Страницы: 4
QCON ProX Setup preview
ProX
Бренд: QCON Страницы: 4
Unipulse F160 Operation Manual preview
F160
Бренд: Unipulse Страницы: 99
Accutrol VTS Installation & Operation Manual preview
VTS
Бренд: Accutrol Страницы: 25
Mainpine EPC Operating Instructions Manual preview
EPC
Бренд: Mainpine Страницы: 16
Danfoss AFP Series Installation Manual preview
AFP Series
Бренд: Danfoss Страницы: 20
Bartlett Genesis LT3140 Technical Manual preview
Genesis LT3140
Бренд: Bartlett Страницы: 5
LAE electronic LF28 Instructions For Installation And Use Manual preview
LF28
Бренд: LAE electronic Страницы: 7
LAE electronic AT1-5 Instructions For Use preview
AT1-5
Бренд: LAE electronic Страницы: 2
Madas M16/RM N.C. DN 65 EEX Technical Manual preview
M16/RM N.C. DN 65 EEX
Бренд: Madas Страницы: 44
RBI FUTERA XLF Series Control Manual preview
FUTERA XLF Series
Бренд: RBI Страницы: 128
RBH Access Technologies UNC100 Hardware Manual preview
UNC100
Бренд: RBH Access Technologies Страницы: 36
S&C PMH Inspection Manual preview
PMH
Бренд: S&C Страницы: 11
S&C BankGuard PLUS Installation Manual preview
BankGuard PLUS
Бренд: S&C Страницы: 24
S&C BankGuard PLUS Operation preview
BankGuard PLUS
Бренд: S&C Страницы: 19
u-blox M8 Series Hardware Integration Manual preview
M8 Series
Бренд: u-blox Страницы: 28
u-blox EVK-NINA-W151 Quick Start preview
EVK-NINA-W151
Бренд: u-blox Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды