manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации, Страница: 121 / 226

Поделиться
Скачать
Siemens Synco700 RMK770 Скачать руководство пользователя страница 121

121/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

7 Boiler temperature control 

01.03.2005 

 

7.13  Boiler faults  

 

If a boiler initiates lockout, it will be shut down until the fault is rectified. 
A boiler is considered faulty if one of the following faults occurred: 

•

  Fault of burner 

•

  Fault of boiler pump 

•

  Fault of shutoff valve (no checkback signal) 

•

  Maximum flue gas temperature exceeded (if plant stop required) 

•

  One of the 3 binary fault inputs reports a fault 

•

  Faulty boiler temperature sensor 

 

  Main menu > Commissioning > Extra configuration > Boiler … > Inputs 

Operating line 

Adjustable values / remarks 

Checkb signal burner 

 

Checkb sign shutoff valve 

 

Fault burner 

 

Fault input 1 

 

Fault input 2 

 

Fault input 3 

 

[Boiler pump] overload 

 

[Boiler pump B] overload 

 

Flow signal pump 

 

 
A burner fault can be signaled by the burner fault input, or it can be generated when 
there is no burner checkback signal from the controller. 
The waiting time for the burner’s checkback signal can be adjusted (signal delay).  
 
If there is no checkback signal from the shutoff valve, the boiler is considered faulty 
also. The waiting time for the checkback signal can be adjusted. If there is no check-
back signal on completion of the waiting time, a fault will be signaled. 
 
It can be selected whether or not crossing of the maximum flue gas temperature shall 
lead to a fault with boiler stop. 
 
There are 3 binary fault inputs available which, with the default parameters, are used 
for water shortage, high-pressure and low-pressure. 
But it is also possible to use other fault text.  
Depending on the kind of fault, the fault status signal delay, the fault acknowledgement, 
the priority and / or the effect can be parameterized. 
 For fault inputs 1, 2 and 3, it is also possible to enter fault text. For details about the 
meaning of these settings, refer to chapter 12 “Function block faults”.  
 

  Main menu > Commissioning > Settings > … 

or

 

  Main menu > Settings > Boiler … > Fault settings > Fault Burner 

Operating line 

Range 

Factory setting 

Fault acknowledgement 

None / Acknowledge /  
Acknowledge and reset 

Acknowledge 

 

  Main menu > Commissioning > Settings > … 

or

 

  Main menu > Settings > Boiler … > Fault settings > Checkb signal burner 

Fault burner 

Fault shutoff valve 

Maximum flue gas 
temperature 

Binary fault inputs 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов