Siemens Synco700 RMK770 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 226

Siemens Synco700 RMK770 Скачать руководство пользователя страница 72

72/226

Building Technologies

Boiler Sequence Controller RMK770

CE1P3132en

HVAC Products

5 General functions, fundamentals

01.03.2005

Main menu > Commissioning > Settings > …

or

Main menu > Settings > Boiler sequence manager > Twin pump
Main menu > Settings > Boiler … > Twin pump
Main menu > Settings > Primary controller > Twin pump
Main menu > Settings > Heating circuit > Twin pump

Operating line

Range

Factory setting

Run priority

Auto / Twin pump A /
Twin pump B

Auto

Changeover period

–60…0…+60 s

0 s

5.8.1 Changeover

logic

For pump changeover, there are 3 choices available:

•

Automatic changeover once a week; should the working pump become faulty,

changeover to the second pump will take place.
When switching on the next time, the pump that starts to run is always the pump that
was in operation last

•

Pump A is always the working pump; in the event of fault, changeover to pump B will

take place. After rectification of the fault, changeover back to pump A will take place

•

Pump B is always the working pump.

In the event of fault, changeover to pump A will take place. After rectification of the
fault, changeover back to pump B will take place

The changeover time is the same time as that used for the pump / mixing valve kick
(kick day and kick time).
For this reason, this setting must be checked.
Automatic changeover takes place on completion of 168 hours (7 days) or – after a new
plant start – when the kick day and kick time are reached.
Even if the pump kick is deactivated, both kick time and kick day remain defined.

Changeover from one pump to the other can take place as follows, depending on the
application:

•

With no interruption

•

With overlapping

•

With interruption

The changeover from pump A to pump B takes place at the same time:

31

31

D

42

A

B

The changeover from pump A to pump B overlaps, e.g. to ensure a low noise level
during changeover. The pump to be deactivated overruns for the adjusted period of
time.

31

31

D

43

A

B

Setting

Run priority

Changeover time

Changeover period

No changeover
delay

Changeover with
negative delay

«
...
70
71
72
73
74
...
»

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов