manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации, Страница: 83 / 226

Поделиться
Скачать
Siemens Synco700 RMK770 Скачать руководство пользователя страница 83

83/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

6 Boiler sequence management 

01.03.2005 

0

20

40

60

80

100

120

140

160

180

200

220

240

260

280

300

320

340

360

380

400

0

20

40

60

80

100

120

140

160

180

200

220

240

260

280

300

320

340

360

380

400

31

32D

01

Heat demand or load

B

o

il

e

r 1

B

o

ile

r 2

B

o

ile

r 3

Bo

il

e

r 4

 

  Burner stage in continuous operation 

  Burner stage cycling 

 

  Main menu > Commissioning > Settings > …

 or

 

  Main menu > Settings >

 

Boiler … > Operation settings 

Operating line 

Range 

Factory setting 

Setpoint increase lag boiler 

0…50 K 

10 K 

 

A great setpoint increase (to be set separately on each boiler) allows the lead boiler to 
provide control while the relevant lag boiler operates at full capacity. This way, it is 
made certain that several boilers with their burner stages do not cycle simultaneously. 

 

With a small setpoint increase, or no increase at all, the relevant lag boiler also pro-
vides control. This can be especially desirable in the case of boiler sequences with 
several modulating burners. 

 

Boiler sequence with 4 boilers and modulating burners as an example. 
Lag boilers with small setpoint increase or no increase at all. 

0

20

40

60

80

100

120

140

160

180

200

220

240

260

280

300

320

340

360

380

400

0

20

40

60

80

100

120

140

160

180

200

220

240

260

280

300

320

340

360

380

400

3132D

02

Heat demand or load

B

o

il

e

r 

1

B

o

ile

r 2

B

o

ile

r 3

B

o

ile

r 4

  Burner stage modulating 

  

In the case of boilers with greatly different capacities (e.g. second boiler twice the ca-
pacity of the first boiler), the second boiler can be put into operation after the first boiler 
and the first boiler is shut down. The first boiler resumes operation only when both 
stages of the second boiler are on. This ensures a better graduation of the total boiler 
output. 
This approach can be chosen only if the output of the basic stage of boiler 2 exceeds 
the rated capacity of boiler 1. If this strategy is chosen, a fixed boiler sequence makes 
sense, thereby ensuring that the same boiler is always boiler no. 2. 

Example 

Binary switching on 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов