manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации, Страница: 166 / 226

Поделиться
Скачать
Siemens Synco700 RMK770 Скачать руководство пользователя страница 166

166/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

10 Heating circuit control 

01.03.2005 

Based on the outside temperature, the building time constant and the rate of room 
temperature increase, the room model calculates the room temperature. 
If no room temperature sensor is connected, the optimization functions can work with 
this room model.  

31

31

D

36

TRw

TRM

Economy

Cmf

TR

t

 

T

RM

 

Room model temperature 

TRw 

Room temperature setpoint 

In the case of sudden positive increases of the room temperature setpoint, the room 
model temperature will be updated at the rate of room temperature increase. In the 
case of sudden negative drops, the room model temperature will approach the compos-
ite outside temperature at 3 times the building time constant, whereby the process is 
stopped as soon as the current room temperature setpoint is reached. 
 

  Main menu > Settings > Heating circuit > Optimizations/influences 

Operating line 

Range 

Factory setting 

Type of optimization 

With room model / With 
room temp sensor 

With room model 

10.8.2   Optimum start / stop control 

 

The purpose of optimum start control is to reach a temperature level 0.25 K below the 
Comfort or Precomfort setpoint when occupancy according to the time program starts.  
For that, the heating circuit must be switched on at an earlier point in time. 
If a room temperature sensor is connected, the controller calculates the forward shift 
depending on the current room temperature. Also, the controller learns the necessary 
heating up time per K room temperature. 
After the required room temperature is reached, the time differential to the entered time 
will be determined. Based on the deviation ascertained, the controller can readjust the 
heating up time per K room temperature and calculate the next forward shift with this 
new value. 
 
If no room temperature sensor is connected, or when the room model shall be used, the 
rate of room temperature increase (duration in min/K) can be set. 
The maximum forward shift can also be set. When entering 0 hours as the maximum 
heating up time, optimum start control will be deactivated. 
 

  Main menu > Settings > Heating circuit > Optimizations/influences 

Operating line 

Range 

Factory setting 

Forward shift on max 

0…48 h 

0 h 

Room temperature rise  

1…600 min/K 

60 min/K 

 
Optimum stop control switches the heating circuit off at the earliest possible point in 
time so that, when the time switch changes from Comfort   or Precomfort   to Econ-

Room model 

Settings 

Optimum start control 

With room model 

Settings 

Optimum stop control 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов