![background image](http://html1.mh-extra.com/html/rands/znb/znb_user-manual_3286757998.webp)
Command Reference
R&S
®
ZNB/ZNBT
998
User Manual 1173.9163.02 ─ 55
CONTrol<Ch>:RFFE<Bus>:SETTings:FREQuency
......................................................... 1013
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:IO
......................................................... 1013
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:LOW
......................................................1013
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:HIGH
.....................................................1013
CONTrol<Ch>:RFFE<Bus>:TEST:DATA
......................................................................... 1014
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk
.......................................................................1014
CONTrol<Ch>:RFFE<Bus>:TEST:VIO
............................................................................1014
CONTrol<Ch>:RFFE<Bus>:TEST:DATA:RANGe
............................................................. 1015
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk:RANGe
...........................................................1015
CONTrol<Ch>:RFFE<Bus>:TEST:VIO:RANGe
................................................................1015
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk:SHUNt?
..........................................................1015
CONTrol<Ch>:RFFE<Bus>:TEST:DATA:SHUNt?
............................................................ 1015
CONTrol<Ch>:RFFE<Bus>:TEST:VIO:SHUNt?
...............................................................1015
CONTrol:RFFE<Bus>:TEST:DATA:VOLTage?
................................................................. 1016
CONTrol:RFFE<Bus>:TEST:CLOCk:VOLTage?
...............................................................1016
CONTrol:RFFE<Bus>:TEST:VIO:VOLTage?
....................................................................1016
CONTrol:RFFE<Bus>:TEST:DATA:CURRent?
................................................................ 1016
CONTrol:RFFE<Bus>:TEST:CLOCk:CURRent?
.............................................................. 1016
CONTrol:RFFE<Bus>:TEST:VIO:CURRent?
................................................................... 1016
CONTrol<Ch>:SEGMent<Nr>:SEQuence:COUNt?
..........................................................1016
CONTrol<Ch>:SEGMent<Nr>:SEQuence:CLEar:ALL
...................................................... 1017
CONTrol<Ch>:SEGMent<Nr>:SEQuence<Nr>:DELay
..................................................... 1017
CONTrol<Ch>:SEGMent<Nr>:SEQuence<Nr>:GPIO<Port>:VOLTage
...............................1017
CONTrol<Ch>:SEGMent<Nr>:SEQuence<Nr>:RFFE<Bus>:COMMand:DATA
CONTrol<Ch>:SEQuence:CLEar:ALL
............................................................................ 1019
................................................................................ 1019
CONTrol<Ch>:SEQuence<Nr>:DELay
........................................................................... 1019
CONTrol<Ch>:SEQuence<Nr>:GPIO<Port>:VOLTage
..................................................... 1020
CONTrol<Ch>:SEQuence<Nr>:RFFE<Bus>:COMMand:DATA
..........................................1020
CONTrol:AUXiliary:C[:DATA]
<DecValue>
Sets or queries a channel-dependent eight-bit decimal value to control eight independ-
ent output signals at the USER PORT connector (lines 8, 9, 10, 11 and lines 16, 17, 18,
19). The output signals are 3.3 V TTL signals which can be used to differentiate
between up to 255 independent analyzer states.
CONTrol:AUXiliary:C[:DATA]
itself does not change the analyzer state.
Channel bit definition and activation
The channel bits have the following properties:
●
After a
*RST
of the analyzer all channel bits (including the value for the active,
sweeping channel no. 1) are set to zero; no signal is applied to pins 8 to 11 and 16
to 19 of the USER PORT connector.
●
The value defined with
CONTrol:AUXiliary:C[:DATA]
is assigned to the
active
).
●
The signals at the USER PORT connector reflect the channel bits of the
measur-
ing
channel, i.e. the channel for which the analyzer performs a sweep. This chan-
nel is not necessarily identical with the active channel.
SCPI Command Reference