JUMO flowTRANS MAG H01 Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 260

background image

139

8 Parameterization

Italics = Parameter can only be viewed in the "Advanced" password level

Gas Bubble Detector

The gas bubble detector can be used in the nominal width range DN 10 to 300. More information



see

chapter 9 "Advanced diagnostics functions", page 153.

Adjust Gas Bubble

Prior to starting the (manual/automatic) calibration, make sure that:
•

There must be no flow through the sensor (close all valves, shut-off devices, etc.).

•

The sensor must be completely filled with the medium to be measured.

Italics = Parameter can only be viewed in the "Advanced" password level

Coating Detector

The electrode deposit detector can be used in the nominal width range DN 10 to 300. More information



see chapter 9 "Advanced diagnostics functions", page 153.

Menu/parameter

Value range

Description

Diagnostics/Diagnostics Control/

Gas Bubble Detector

a

Gas Bubble Detector

ON/OFF

Activates the "Gas Bubble Detector" function
Default setting: OFF

Adjust Gas Bubble

The Gas Bubble Detector must be calibrated to the
local conditions. Start automatic gas bubble detection
calibration.

Threshold Gas Bubble

Setting the switching threshold. If the current value is
above the set switching threshold, a message is out-
put on the LCD display and the alarm is activated at
the digital output, if configured accordingly.

Gas Bubble Value

Display only

Display the current Gas Bubble Value

a

Only available for JUMO flowTRANS MAG S02/H02

?
?

Menu/parameter

Value range

Description

Diagnostics/Diagnostics Control/

Coating Detector

a

Coating Detector

ON/OFF

Activates the "Coating Detector" function
Default setting: OFF

One Shot Coating

The electrode deposit is measured cyclically at spec-
ified intervals. A one-off measurement can be initiat-
ed here.

Coating Value QE1

Display only

Current deposit value for electrode 1

Coating Value QE2

Display only

Current deposit value for electrode 2

Coating QE Min. Alarm

0 to 100,000

Setting of the minimum limit value for detection of de-
posits. The smaller value of QE1, QE2 triggers an
alarm if below the threshold.
Default setting: 0

Coating QE Max. Alarm

0 to 100,000

Setting of the minimum limit value for detection of de-
posits. The smaller value of QE1, QE2 triggers an
alarm if below the threshold.
Default setting: 100.000

a

Only available for JUMO flowTRANS MAG S02/H02

?

«
...
137
138
139
140
141
...
»

Содержание flowTRANS MAG H01





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для flowTRANS MAG H01

Бренд: Abbott Страницы: 296

Бренд: Camille Bauer Страницы: 11

Бренд: Camille Bauer Страницы: 83

Бренд: HANSA-FLEX Страницы: 23

Бренд: Keysight Страницы: 92

Бренд: ISKRAEMECO Страницы: 12

RAVTD1760WS Series

Бренд: Ravaglioli Страницы: 24

DT4120 PS Series

Бренд: Datcon Страницы: 92

Бренд: FM Marin Страницы: 8

Thermo Scientific iCE 3000 Series

Бренд: ThermoFisher Scientific Страницы: 42

Бренд: BAPI Страницы: 3

SXP30 - ELECTRONIC PIANO

Бренд: Technics Страницы: 12

Бренд: IME Страницы: 14

Xevo TQ-XS Mass

Бренд: Waters Страницы: 213

Бренд: Jedia Страницы: 11

Бренд: Fluke Biomedical Страницы: 34

Бренд: ADCMT Страницы: 28

Бренд: Zenner Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды