JUMO flowTRANS MAG H01 Скачать руководство пользователя страница 74

Страница: 74 / 260

7 Startup

7.2.1

Transmitter - dual-compartment housing

Configure the outputs as follows:

1. Switch off the voltage supply.

2. Open the case lid.

3. Remove the fastening screws for the transmitter electronics unit.

4. Pull out the transmitter electronics unit.

5. Set jumpers on the backplane according to the following table.

6. Reinstall the transmitter electronics unit in reverse order.

JUMO flowTRANS MAG S/H - compact design

JUMO flowTRANS MAG - remote mount design

(1)

Case lid

(2)

Transmitter plug-in module

(3)

Mounting screws

(4)

Backplane (in the transmitter housing)

(5)

Jumper (BR901) for active/passive current output

(6)

Jumper (BR903) for integral/remote mount design

(7)

Jumper (BR902) for hardware write protection

IMPORTANT (NOTE)!

The backplane is mounted in the transmitter housing (not the transmitter plug-in module).

Jumper

Position

Function

BR901

active

Current output 31/32 active

passive

Current output 31/32 passive

BR902

Read only

Hardware write protection active

BR903

Integral

Transmitter with compact design

Remote

Transmitter with remote mount design

Содержание flowTRANS MAG H01





































































































































































































































































Результаты поиска

Содержание flowTRANS MAG H01

Отзывы:

Похожие инструкции для flowTRANS MAG H01

Бренды по названию

Популярные бренды

JUMO flowTRANS MAG H01, Руководство по эксплуатации

Результаты поиска

Содержание flowTRANS MAG H01

Отзывы:

Похожие инструкции для flowTRANS MAG H01

Бренды по названию

Популярные бренды