manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 74 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 74

Configuring the Switch

3-22

3

To delete a file select System, File Management, Delete. Select the file name from 
the given list by checking the tick box and click Apply. Note that the file currently 
designated as the startup code cannot be deleted.

Figure 3-12   Deleting Files

CLI

 – To download new firmware form a TFTP server, enter the IP address of the 

TFTP server, select “config” as the file type, then enter the source and destination 
file names. When the file has finished downloading, set the new file to start up the 
system, and then restart the switch.

To start the new firmware, enter the “reload” command or reboot the system.

Console#copy tftp file

4-64

TFTP server ip address: 10.1.0.19
Choose file type:

1. config:

2. opcode: <1-2>: 2

Source file name: V3.1.1.21.bix
Destination file name: V31121
\Write to FLASH Programming.
-Write to FLASH finish.
Success.
Console#config
Console(config)#boot system opcode:V31121

4-69

Console(config)#exit
Console#reload

4-23

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов