manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 349 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 349

General Commands

4-21

4

Default Setting

Level 15

Command Mode

Normal Exec

Command Usage 

• “super” is the default password required to change the command mode from 

Normal Exec to Privileged Exec. (To set this password, see the 

enable 

password

 command on page 4-28.)

• The “#” character is appended to the end of the prompt to indicate that the 

system is in privileged access mode. 

Example 

Related Commands 

disable (4-21)
enable password (4-28)

disable

This command returns to Normal Exec mode from privileged mode. In normal 
access mode, you can only display basic information on the switch's configuration or 
Ethernet statistics. To gain access to all commands, you must use the privileged 
mode. See “Understanding Command Modes” on page 4-6.

Default Setting 

None

Command Mode 

Privileged Exec

Command Usage 

The “>” character is appended to the end of the prompt to indicate that the 
system is in normal access mode.

Example 

Related Commands 

enable (4-20)

Console>enable
Password: [privileged level password]
Console#

Console#disable
Console>

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов