Edge-Core ES4625 Скачать руководство пользователя страница 533

Страница: 533 / 674

GVRP and Bridge Extension Commands

4-205

Example

Related Commands

show garp timer (4-205)

show garp timer

This command shows the GARP timers for the selected interface.

Syntax

show garp timer

[

interface

]

interface

•

ethernet

unit

port

unit

- Stack unit. (Range: 1-8)

port

- Port number. (Range: 1-25/49)

•

port-channel

channel-id

(Range: 1-32)

Default Setting

Shows all GARP timers.

Command Mode

Normal Exec, Privileged Exec

Example

Related Commands

garp timer (4-204)

Console(config)#interface ethernet 1/1
Console(config-if)#garp timer join 100
Console(config-if)#

Console#show garp timer ethernet 1/1
Eth 1/ 1 GARP timer status:

Join timer:

20 centiseconds

Leave timer:

60 centiseconds

Leaveall timer: 1000 centiseconds

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 533 / 674

Результаты поиска

Содержание ES4625

Отзывы: