manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 625 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 625

Multicast Routing Commands

4-297

4

General Multicast Routing Commands

 

ip multicast-routing

This command enables IP multicast routing. Use the 

no

 form to disable IP multicast 

routing.

Syntax 

[

no

]

 ip multicast-routing

Default Setting 

Disabled

Command Mode 

Global Configuration

Command Usage 

This command is used to enable multicast routing globally for the router. You 
also need to globally enable a specific multicast routing protocol using the 

router dvmrp

 or 

router pim

 command, and then specify the interfaces that 

will support multicast routing using the 

ip dvmrp

 or 

ip pim dense-mode

 

commands.

Example 

show ip mroute

This command displays the IP multicast routing table.

Syntax 

show ip mroute 

[

group-address source

] [

summary

] 

•

group-address

 - An IP multicast group address with subscribers directly 

attached or downstream from this router.

• source

 - The IP subnetwork at the root of the multicast delivery tree. This 

subnetwork contains a known multicast source.

•

summary

 -

 Displays summary information for each entry in the IP multicast 

routing table.

Command Mode 

Privileged Exec

Table 4-104   General Multicast Routing Commands

Command

Function

Mode

Page

ip multicast-routing

Enables IP multicast routing

GC

4-297

show ip mroute

Shows the IP multicast routing table

PE

4-297

Console(config)#ip multicast-routing
Console(config)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов