manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 270 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 270

Configuring the Switch

3-218

3

Web -

 Click IP, Statistics, IP.

Figure 3-125   IP Statistics

CLI -

 See the example on page 3-215.

ICMP Statistics

Internet Control Message Protocol (ICMP) is a network layer protocol that transmits 
message packets to report errors in processing IP packets. ICMP is therefore an 
integral part of the Internet Protocol. ICMP messages may be used to report various 
situations, such as when a datagram cannot reach its destination, when the gateway 
does not have the buffering capacity to forward a datagram, and when the gateway 
can direct the host to send traffic on a shorter route. ICMP is also used by routers to 
feed back information about more suitable routes (i.e., the next hop router) to use for 
a specific destination. 

Table 3-19   ICMP Statistics

Parameter

Description

Messages

The total number of ICMP messages which the entity received/sent.

Errors

The number of ICMP messages which the entity received/sent but 

determined as having ICMP-specific errors (bad ICMP checksums, bad 

length, etc.).

Destination Unreachable

The number of ICMP Destination Unreachable messages received/sent.

Time Exceeded

The number of ICMP Time Exceeded messages received/sent.

Parameter Problems

The number of ICMP Parameter Problem messages received/sent.

Source Quenches

The number of ICMP Source Quench messages received/sent.

Redirects

The number of ICMP Redirect messages received/sent.

Echos

The number of ICMP Echo (request) messages received/sent.

Echo Replies

The number of ICMP Echo Reply messages received/sent.

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов