Edge-Core ES4625 Скачать руководство пользователя страница 429

Страница: 429 / 674

Access Control List Commands

4-101

•

vid-bitmask

–

VLAN bitmask. (Range: 1-4093)

•

protocol

– A specific Ethernet protocol number. (Range: 600-fff hex.)

•

protocol

bitmask

– Protocol bitmask. (Range: 600-fff hex.)

Default Setting

None

Command Mode

MAC ACL

Command Usage

• New rules are added to the end of the list.
• The

ethertype

option can only be used to filter Ethernet II formatted packets.

• A detailed listing of Ethernet protocol types can be found in RFC 1060. A few

of the more common types include the following:
- 0800 - IP
- 0806 - ARP
- 8137 - IPX

Example

This rule permits packets from any source MAC address to the destination address
00-e0-29-94-34-de where the Ethernet type is 0800.

Related Commands

access-list mac (4-99)

show mac access-list

This command displays the rules for configured MAC ACLs.

Syntax

show mac access-list

[

acl_name

]

acl_name

– Name of the ACL. (Maximum length: 16 characters)

Command Mode

Privileged Exec

Example

Related Commands

permit, deny 4-100
mac access-group (4-105)

Console(config-mac-acl)#permit any host 00-e0-29-94-34-de ethertype 0800
Console(config-mac-acl)#

Console#show mac access-list
MAC access-list jerry:

permit any 00-e0-29-94-34-de ethertype 0800

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 429 / 674

Результаты поиска

Содержание ES4625

Отзывы: