Edge-Core ES4625 Скачать руководство пользователя страница 142

Страница: 142 / 674

Configuring the Switch

3-90

•

Broadcast storm

– Shows if broadcast storm control is enabled or disabled.

•

Broadcast storm limit

– Shows the broadcast storm threshold. (500 - 262143

packets per second)

•

Flow control

– Shows if flow control is enabled or disabled.

•

LACP

– Shows if LACP is enabled or disabled.

•

Port security

– Shows if port security is enabled or disabled.

•

Max MAC count

– Shows the maximum number of MAC address that can be

learned by a port. (0 - 1024 addresses)

•

Port security action

– Shows the response to take when a security violation is

detected. (shutdown, trap, trap-and-shutdown)

•

Media type

– Shows the forced/preferred port type to use for combination ports

21-24 (ES4625) or 45-48 (ES4649). (copper forced, SFP forced, SFP preferred auto)

Current status:

•

Link status

– Indicates if the link is up or down.

•

Port operation status

– Provides detailed information on port state.

(Displayed only when the link is up.).

•

Operation speed-duplex

– Shows the current speed and duplex mode.

•

Flow control type

– Indicates the type of flow control currently in use.

(IEEE 802.3x, Back-Pressure or none)

CLI

– This example shows the connection status for Port 5.

8. There are interoperability problems between Flow Control and Head-of-Line (HOL) blocking

for the switch ASIC; Flow Control is therefore not supported for this switch.

Console#show interfaces status ethernet 1/5

4-150

Information of Eth 1/13

Basic information:

Port type:

1000T

Mac address:

00-30-F1-D4-73-A5

Configuration:

Name:
Port admin:

Speed-duplex:

Auto

Capabilities:

10half, 10full, 100half, 100full, 1000full

Broadcast storm:

Enabled

Broadcast storm limit:

500 packets/second

Flow control:

Disabled

LACP:

Disabled

Port security:

Disabled

Max MAC count:

Port security action:

None

Media type:

None

Current status:

Link status:

Down

Operation speed-duplex: 1000full
Flow control type:

None

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 142 / 674

Результаты поиска

Содержание ES4625

Отзывы: