manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 560 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 560

Command Line Interface

4-232

4

Default Setting 

10 seconds

Command Mode 

Global Configuration

Command Usage

• The switch must be using IGMPv2 for this command to take effect. 
• This command defines the time after a query, during which a response is 

expected from a multicast client. If a querier has sent a number of queries 
defined by the 

ip igmp snooping query-count

, but a client has not 

responded, a countdown timer is started using an initial value set by this 
command. If the countdown finishes, and the client still has not responded, 
then that client is considered to have left the multicast group. 

Example 

The following shows how to configure the maximum response time to 20 seconds:

Related Commands 

ip igmp snooping version (4-228)
ip igmp snooping query-max-response-time (4-231)

ip igmp snooping router-port-expire-time

This command configures the query timeout. Use the 

no

 form to restore the default.

Syntax 

ip igmp snooping router-port-expire-time

 

seconds

no ip igmp snooping router-port-expire-time

seconds

 - The time the switch waits after the previous querier stops before 

it considers the router port (i.e., the interface which had been receiving 
query packets) to have expired. 
(Range: 300-500)

Default Setting 

300 seconds

Command Mode 

Global Configuration

Command Usage 

The switch must use IGMPv2 for this command to take effect.

Console(config)#ip igmp snooping query-max-response-time 20
Console(config)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов