manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 209 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 209

Class of Service Configuration

3-157

3

Mapping IP Precedence

The Type of Service (ToS) octet in the IPv4 header includes three precedence bits 
defining eight different priority levels ranging from highest priority for network control 
packets to lowest priority for routine traffic. The default IP Precedence values are 
mapped one-to-one to Class of Service values (i.e., Precedence value 0 maps to 
CoS value 0, and so forth). Bits 6 and 7 are used for network control, and the other 
bits for various application types. ToS bits are defined in the following table.

Command Attributes

•

IP Precedence Priority Table 

–

 

Shows the IP Precedence to CoS map.

•

Class of Service Value 

–

 

Maps a CoS value to the selected IP Precedence value. 

Note that “0” represents low priority and “7” represent high priority.

Web

 – Click Priority, IP Precedence Priority. Select an entry from the IP Precedence 

Priority Table, enter a value in the Class of Service Value field, and then click Apply. 

Figure 3-91   IP Precedence Priority

Table 3-14   Mapping IP Precedence

Priority Level

Traffic Type

Priority Level

Traffic Type

7

Network Control

3

Flash

6

Internetwork Control

2

Immediate

5

Critical

1

Priority

4

Flash Override

0

Routine

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов