manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 450 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 450

Command Line Interface

4-122

4

Command Usage 

This command is used to include a client identifier in all communications with 
the DHCP server. The identifier type depends on the requirements of your 
DHCP server. 

Example

Related Commands

ip dhcp restart client (4-122)

ip dhcp restart client

This command submits a BOOTP or DHCP client request.

Default Setting 

None

Command Mode 

Privileged Exec

Command Usage 

• This command issues a BOOTP or DHCP client request for any IP interface 

that has been set to BOOTP or DHCP mode via the 

ip address

 command.

• DHCP requires the server to reassign the client’s last address if available. 
• If the BOOTP or DHCP server has been moved to a different domain, the 

network portion of the address provided to the client will be based on this new 
domain. 

Example 

In the following example, the device is reassigned the same address.

Related Commands 

 ip address (4-242)

Console(config)#interface vlan 2
Console(config-if)#ip dhcp client-identifier hex 00-00-e8-66-65-72
Console(config-if)#

Console(config)#interface vlan 1
Console(config-if)#ip address dhcp
Console(config-if)#exit
Console#ip dhcp restart client
Console#show ip interface

Vlan 1 is up, addressing mode is DHCP

Interface address is 192.168.1.54, mask is 255.255.255.0, Primary
MTU is 1500 bytes
Proxy ARP is disabled
Split horizon is enabled

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов