Edge-Core ES4625 Скачать руководство пользователя страница 382 | Manualshive

Страница: 382 / 674

Edge-Core ES4625 Скачать руководство пользователя страница 382

Command Line Interface

4-54

4

Example

Related Commands

sntp server (4-54)
sntp poll (4-55)
show sntp (4-55)

sntp server

This command sets the IP address of the servers to which SNTP time requests are
issued. Use the this command with no arguments to clear all time servers from the
current list.

Syntax

sntp server

[

ip1

[

ip2

[

ip3

]]]

ip

- IP address of an time server (NTP or SNTP).

(Range: 1 - 3 addresses)

Default Setting

None

Command Mode

Global Configuration

Command Usage

This command specifies time servers from which the switch will poll for time
updates when set to SNTP client mode. The client will poll the time servers in
the order specified until a response is received. It issues time synchronization
requests based on the interval set via the

sntp poll

command.

Example

Related Commands

sntp client (4-53)
sntp poll (4-55)
show sntp (4-55)

Console(config)#sntp server 10.1.0.19
Console(config)#sntp poll 60
Console(config)#sntp client
Console(config)#end
Console#show sntp
Current time:

Dec 23 02:52:44 2002

Poll interval: 60
Current mode: unicast
SNTP status : Enabled
SNTP server 137.92.140.80 0.0.0.0 0.0.0.0
Current server: 137.92.140.80
Console#

Console(config)#sntp server 10.1.0.19
Console#

«
...
380
381
382
383
384
...
»

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов