Edge-Core ES4625 Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 674

Edge-Core ES4625 Скачать руководство пользователя страница 151

Port Configuration

3-99

3

CLI

– The following example configures LACP parameters for ports 1-10. Ports 1-8

are used as active members of the LAG, ports 9 and 10 are set to backup mode.

Console(config)#interface ethernet 1/1

4-143

Console(config-if)#lacp actor system-priority 3

4-160

Console(config-if)#lacp actor admin-key 120

4-161

Console(config-if)#lacp actor port-priority 128

4-162

Console(config-if)#exit

.

.

.
Console(config)#interface ethernet 1/10
Console(config-if)#lacp actor system-priority 3
Console(config-if)#lacp actor admin-key 120
Console(config-if)#lacp actor port-priority 512
Console(config-if)#end
Console#show lacp sysid

4-163

Channel Group

System Priority

System MAC Address

-------------------------------------------------------------------------

1

3

00-00-E9-31-31-31

2

32768

00-00-E9-31-31-31

3

32768

00-00-E9-31-31-31

.

.

.
Console#show lacp 1 internal

4-163

Port channel: 1
-------------------------------------------------------------------------
Oper Key:

120

Admin Key: 0
Eth 1/ 1
-------------------------------------------------------------------------

LACPDUs Internal:

30 sec

LACP System Priority: 3
LACP Port Priority:

128

Admin Key:

120

Oper Key:

120

Admin State: defaulted, aggregation, long timeout, LACP-activity
Oper State:

distributing, collecting, synchronization,
aggregation, long timeout, LACP-activity

.

.

.

«
...
149
150
151
152
153
...
»

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов