Edge-Core ES4625 Скачать руководство пользователя страница 523

Страница: 523 / 674

VLAN Commands

4-195

switchport forbidden vlan

This command configures forbidden VLANs. Use the

form to remove the list of

forbidden VLANs.

Syntax

switchport forbidden vlan

{

add

vlan-list

remove

vlan-list

}

no switchport forbidden vlan

•

add

vlan-list

- List of VLAN identifiers to add.

•

remove

vlan-list

- List of VLAN identifiers to remove.

•

vlan-list

- Separate nonconsecutive VLAN identifiers with a comma and no

spaces; use a hyphen to designate a range of IDs. Do not enter leading
zeros. (Range: 1-4093).

Default Setting

No VLANs are included in the forbidden list.

Command Mode

Interface Configuration (Ethernet, Port Channel)

Command Usage

• This command prevents a VLAN from being automatically added to the

specified interface via GVRP.

• If a VLAN has been added to the set of allowed VLANs for an interface, then

you cannot add it to the set of forbidden VLANs for that same interface.

Example

The following example shows how to prevent port 1 from being added to VLAN 3:

Displaying VLAN Information

Console(config)#interface ethernet 1/1
Console(config-if)#switchport forbidden vlan add 3
Console(config-if)#

Table 4-62 Commands for Displaying VLAN Information

Command

Function

Mode

Page

show vlan

Shows VLAN information

NE, PE

4-196

show interfaces status vlan Displays status for the specified VLAN interface

NE, PE

4-150

show interfaces switchport

Displays the administrative and operational status of an

interface

NE, PE

4-152

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 523 / 674

Результаты поиска

Содержание ES4625

Отзывы: