manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 610 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 610

Command Line Interface

4-282

4

ip ospf transmit-delay

This command sets the estimated time to send a link-state update packet over an 
interface. Use the 

no

 form to restore the default value.

Syntax 

ip ospf transmit-delay

 seconds

no ip ospf transmit-delay

seconds

 - Sets the estimated time required to send a link-state update. 

(Range: 1-65535)

Command Mode 

Interface Configuration (VLAN)

Default Setting 

1 second

Command Usage 

LSAs have their age incremented by this delay before transmission. When 
estimating the transmit delay, consider both the transmission and propagation 
delays for an interface. Set the transmit delay according to link speed, using 
larger values for lower-speed links. The transmit delay must be the same for 
all routers attached to an autonomous system.

Example

show ip ospf

This command shows basic information about the routing configuration.

Command Mode 

Privileged Exec

Example

Console(config)#interface vlan 1
Console(config-if)#ip ospf transmit-delay 6
Console(config-if)#

Console#show ip ospf
Routing Process with ID 10.1.1.253
Supports only single TOS(TOS0) route
It is an area border and autonomous system boundary router
Redistributing External Routes from,

rip with metric mapped to 10

Number of area in this router is 2
Area 0.0.0.0 (BACKBONE)

Number of interfaces in this area is 1
SPF algorithm executed 19 times

Area 10.1.0.0

Number of interfaces in this area is 4
SPF algorithm executed 19 times

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов