Edge-Core ES4625 Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 674

Edge-Core ES4625 Скачать руководство пользователя страница 133

Access Control Lists

3-81

3

Configuring a MAC ACL

Command Attributes

•

Action

– An ACL can contain any combination of permit or deny rules.

•

Source/Destination

Address Type – Use “Any” to include all possible addresses,

“Host” to indicate a specific MAC address, or “MAC” to specify an address range
with the Address and Bitmask fields. (Options: Any, Host, MAC; Default: Any)

•

Source/Destination MAC Address

– Source or destination MAC address.

•

Source/Destination MAC Bit Mask

– Hexidecimal mask for source or destination

MAC address.

•

VID

– VLAN ID. (Range: 1-4093)

•

VID Bit Mask

– VLAN bitmask. (Range: 1-4093)

•

Ethernet Type

– This option can only be used to filter Ethernet II formatted

packets. (Range: 600-fff hex.)
A detailed listing of Ethernet protocol types can be found in RFC 1060. A few of the
more common types include 0800 (IP), 0806 (ARP), 8137 (IPX).

•

Ethernet Type Bit Mask

– Protocol bitmask. (Range: 600-fff hex.)

•

Packet Format

– This attribute includes the following packet types:

-

Any

– Any Ethernet packet type.

-

Untagged-eth2

– Untagged Ethernet II packets.

-

Untagged-802.3

– Untagged Ethernet 802.3 packets.

-

Tagged-eth2

– Tagged Ethernet II packets.

-

Tagged-802.3

– Tagged Ethernet 802.3 packets.

Command Usage

Egress MAC ACLs only work for destination-mac-known packets, not for multicast,
broadcast, or destination-mac-unknown packets.

«
...
131
132
133
134
135
...
»

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов