manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 212 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 212

Configuring the Switch

3-160

3

Mapping IP Port Priority

You can also map network applications to Class of Service values based on the IP 
port number (i.e., TCP/UDP port number) in the frame header. Some of the more 
common TCP service ports include: HTTP: 80, FTP: 21, Telnet: 23 and POP3: 110. 

Command Attributes

•

IP Port Priority Status

 – Enables or disables the IP port priority.

•

IP Port Priority Table

 – Shows the IP port to CoS map.

•

IP Port Number (TCP/UDP)

 – Set a new IP port number.

•

Class of Service Value

 – Sets a CoS value for a new IP port. Note that “0” 

represents low priority and “7” represent high priority.

Note:

 IP Port Priority settings apply to all interfaces.

Web

 – Click Priority, IP Port Status. Set IP Port Priority Status to Enabled. 

Figure 3-93   IP Port Priority Status

Click Priority, IP Port Priority. Enter the port number for a network application in the 
IP Port Number box and the new CoS value in the Class of Service box, and then 
click Apply.

Figure 3-94   IP Port Priority

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов