manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 222 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 222

Configuring the Switch

3-170

3

Based on the group membership information learned from IGMP, a router/switch can 
determine which (if any) multicast traffic needs to be forwarded to each of its ports. 
At Layer 3, multicast routers use this information, along with a multicast routing 
protocol such as DVMRP or PIM, to support IP multicasting across the Internet.

Note that IGMP neither alters nor routes IP multicast packets. A multicast routing 
protocol must be used to deliver IP multicast packets across different subnetworks. 
Therefore, when DVMRP or PIM routing is enabled for a subnet on this switch, you 
also need to enable IGMP.

Layer 2 IGMP 

(Snooping and Query)

IGMP Snooping and Query – If multicast routing is not supported on other switches 
in your network, you can use IGMP Snooping and IGMP Query (page 3-171) to 
monitor IGMP service requests passing between multicast clients and servers, and 
dynamically configure the switch ports which need to forward multicast traffic. 

Static IGMP Router Interface – If IGMP snooping cannot locate the IGMP querier, 
you can manually designate a known IGMP querier (i.e., a multicast router/switch) 
connected over the network to an interface on your switch (page 3-174). This 
interface will then join all the current multicast groups supported by the attached 
router/switch to ensure that multicast traffic is passed to all appropriate interfaces 
within the switch.

Static IGMP Host Interface – For multicast applications that you need to control 
more carefully, you can manually assign a multicast service to specific interfaces on 
the switch (page 3-176). 

IGMP Query (Layer 2 or 3) – IGMP Query can only be enabled globally at Layer 2, 
but can be enabled for individual VLAN interfaces at Layer 3 (page 3-176). However, 
note that Layer 2 query is disabled if Layer 3 query is enabled.

L3 - network core
(multicast routing)

L2 - edge switches
(snooping and query)

L2 switch to end nodes
(snooping on IGMP clients)

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов