Edge-Core ES4625 Скачать руководство пользователя страница 266

Страница: 266 / 674

Configuring the Switch

3-214

CLI -

This example shows all entries in the ARP cache.

Displaying Local ARP Entries

The ARP cache also contains entries for local interfaces, including subnet, host, and
broadcast addresses.

Command Attributes

•

IP Address

– IP address of a local entry in the cache.

•

MAC Address

– MAC address mapped to the corresponding IP address.

•

Interface

– VLAN interface associated with the address entry.

•

Entry Count

– The number of local entries in the ARP cache.

Web -

Click IP, ARP, Other Addresses.

Figure 3-123 ARP Other Addresses

Console#show arp

4-247

Arp cache timeout: 1200 (seconds)

IP Address

MAC Address

Type

Interface

--------------- ----------------- --------- -----------

10.1.0.0 ff-ff-ff-ff-ff-ff

other

10.1.0.11 00-11-22-33-44-55

static

10.1.0.12 01-02-03-04-05-06

static

10.1.0.19 00-10-b5-62-03-74

dynamic

10.1.0.253 00-00-ab-cd-00-00

other

10.1.0.255 ff-ff-ff-ff-ff-ff

other

Total entry : 6
Console#clear arp-cache

4-247

This operation will delete all the dynamic entries in ARP Cache.
Are you sure to continue this operation (y/n)?y
Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 266 / 674

Результаты поиска

Содержание ES4625

Отзывы: