manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 566 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 566

Command Line Interface

4-238

4

Command Mode 

Interface Configuration (VLAN)

Command Usage

• A multicast client sends an IGMP leave message when it leaves a group. The 

router then checks to see if this was the last host in the group by sending an 
IGMP query and starting a timer based on this command. If no reports are 
received before the timer expires, the group is deleted.

• This value may be tuned to modify the leave latency of the network. A reduced 

value results in reduced time to detect the loss of the last member of a group.

Example 

The following shows how to configure the maximum response time to 10 seconds:

ip igmp version

This command configures the IGMP version used on an interface. Use the 

no

 form 

of this command to restore the default.

Syntax 

ip igmp version

 {

1

 | 

2

}

no ip igmp version

•

1

 - IGMP Version 1 

•

2

 - IGMP Version 2 

Default Setting 

IGMP Version 2

Command Mode 

Interface Configuration (VLAN)

Command Usage

• All routers on the subnet must support the same version. However, the 

multicast hosts on the subnet may support either IGMP version 1 or 2.

• The switch must be set to version 2 to enable the 

ip igmp max-resp-interval

 

(page 4-237).

Example 

The following configures the switch to use IGMP Version 1 on the selected interface:

Console(config-if)#ip igmp last-memb-query-interval 10
Console(config-if)#

Console(config-if)#ip igmp version 1
Console(config-if)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов