manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 563 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 563

Multicast Filtering Commands

4-235

4

ip igmp

This command enables IGMP on a VLAN interface. Use the 

no

 form of this 

command to disable IGMP on the specified interface.

Syntax 

[

no

]

 ip igmp

Default Setting 

Disabled

Command Mode 

Interface Configuration (VLAN)

Command Usage 

IGMP query can be enabled globally at Layer 2 via the 

ip igmp snooping

 

command, or enabled for specific VLAN interfaces at Layer 3 via the 

ip igmp

 

command. (Layer 2 query is disabled if Layer 3 query is enabled.)

Example

Related Commands 

ip igmp snooping (4-227)
show ip igmp snooping (4-228)

ip igmp robustval 

This command specifies the robustness (i.e., expected packet loss) for this 
interface. Use the 

no

 form of this command to restore the default value.

Syntax 

ip igmp robustval 

robust-value

no ip igmp robustval

robust-value

 - The robustness of this interface. (Range: 1-255)

Default Setting 

2

Command Mode 

Interface Configuration (VLAN)

Console(config)#interface vlan 1
Console(config-if)#ip igmp
Console(config-if)#end
Console#show ip igmp interface
Vlan 1 is up

IGMP is enable, version is 2
Robustness variable is 2
Query interval is 125 sec
Query Max Response Time is 10 sec, Last Member Query Interval is 1 sec
Querier is 10.1.0.253

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов