Edge-Core ES4625 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 674

Edge-Core ES4625 Скачать руководство пользователя страница 138

Configuring the Switch

3-86

3

Configuring a MAC ACL Mask

This mask defines the fields to check in the packet header.

Command Usage

You must configure a mask for an ACL rule before you can bind it to a port.

Command Attributes

•

Source/Destination Address Type

– Use “Any” to match any address, “Host” to

specify the host address for a single node, or “MAC” to specify a range of
addresses. (Options: Any, Host, MAC; Default: Any)

•

Source/Destination Bit Mask

– Address of rule must match this bitmask.

•

VID Bitmask

– VLAN ID of rule must match this bitmask.

•

Ethernet Type Bit Mask

– Ethernet type of rule must match this bitmask.

•

Packet Format Mask

– A packet format must be specified in the rule.

Web

– Configure the mask to match the required rules in the MAC ingress or egress

ACLs. Set the mask to check for any source or destination address, a host address,
or an address range. Use a bitmask to search for specific VLAN ID(s) or Ethernet
type(s). Or check for rules where a packet format was specified. Then click Add.

Figure 3-51 ACL Mask Configuration - MAC

«
...
136
137
138
139
140
...
»

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов