manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 379 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 379

System Management Commands

4-51

4

Command Usage 

The specified level indicates an event threshold. All events at this level or 
higher will be sent to the configured email recipients. (For example, using 
Level 7 will report all events from level 7 to level 0.)

Example

This example will send email alerts for system errors from level 3 through 0.

logging sendmail source-email

This command sets the email address used for the “From” field in alert messages. 

Syntax

logging sendmail source-email

 email-address

email-address

 - The source email address used in alert messages. 

(Range: 1-41 characters) 

Default Setting 

None 

Command Mode 

Global Configuration

Command Usage 

You may use an symbolic email address that identifies the switch, or the 
address of an administrator responsible for the switch.

Example

logging sendmail destination-email

This command specifies the email recipients of alert messages. Use the 

no

 form to 

remove a recipient.

Syntax

[

no

] 

logging sendmail destination-email

 email-address

email-address

 - The source email address used in alert messages. 

(Range: 1-41 characters) 

Default Setting 

None 

Command Mode 

Global Configuration

Console(config)#logging sendmail level 3
Console(config)#

Console(config)#logging sendmail source-email [email protected]
Console(config)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов