manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 536 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 536

Command Line Interface

4-208

4

• This switch provides eight priority queues for each port. It is configured to use 

Weighted Round Robin, which can be viewed with the 

show queue 

bandwidth

 command. Inbound frames that do not have VLAN tags are 

tagged with the input port’s default ingress user priority, and then placed in the 
appropriate priority queue at the output port. The default priority for all ingress 
ports is zero. Therefore, any inbound frames that do not have priority tags will 
be placed in queue 0 of the output port. (Note that if the output port is an 
untagged member of the associated VLAN, these frames are stripped of all 
VLAN tags prior to transmission.)

Example 

The following example shows how to set a default priority on port 3 to 5:

queue bandwidth 

This command assigns weighted round-robin (WRR) weights to the eight class of 
service (CoS) priority queues. Use the 

no

 form to restore the default weights.

Syntax 

queue bandwidth

 

weight1...weight4

no queue bandwidth

weight1...weight4

 - The ratio of weights for queues 0 - 7 determines the 

weights used by the WRR scheduler. (Range: 1 - 15)

Default Setting 

Weights 1, 2, 4, 6, 8, 10, 12, 14 are assigned to queues 0 - 7 respectively.

Command Mode 

Interface Configuration (Ethernet, Port Channel)

Command Usage 

WRR controls bandwidth sharing at the egress port by defining scheduling 
weights.

Example 

This example shows how to assign WRR weights to each of the priority queues:

Related Commands

show queue bandwidth (4-210)

Console(config)#interface ethernet 1/3
Console(config-if)#switchport priority default 5

Console#configure
Console(config)#int eth 1/5
Console(config-if)#queue bandwidth 1 3 5 7 9 11 13 15
Console(config-if)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов