manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 462 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 462

Command Line Interface

4-134

4

hardware-address

This command specifies the hardware address of a DHCP client. This command is 
valid for manual bindings only. Use the 

no

 form to remove the hardware address.

Syntax

hardware-address

 

hardware-address type

no hardware-address

•

hardware-address

 - Specifies the MAC address of the client device.

•

type

 - Indicates the following protocol used on the client device:

- ethernet
- ieee802
- fddi

Default Setting 

If no type is specified, the default protocol is Ethernet.

Command Mode

DHCP Pool Configuration

Command Usage 

This command identifies a DHCP or BOOTP client to bind to an address 
specified in the 

host

 command. BOOTP clients cannot transmit a client 

identifier. To bind an address to a BOOTP client, you must associate a 
hardware address with the host entry.

Example

Related Commands

host (4-132)

clear ip dhcp binding

This command deletes an automatic address binding from the DHCP server 
database.

Syntax 

clear ip dhcp binding

 {

address

 | 

*

 }

•

address

 - The address of the binding to clear.

•

*

 - Clears all automatic bindings.

Default Setting 

None

Command Mode

Privileged Exec

Console(config-dhcp)#hardware-address 00-e0-29-94-34-28 ethernet
Console(config-dhcp)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов