manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 635 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 635

Multicast Routing Commands

4-307

4

show ip dvmrp neighbor

This command displays all of the DVMRP neighbor routers.

Command Mode 

Normal Exec, Privileged Exec

Example 

show ip dvmrp interface

This command displays the DVMRP configuration for interfaces which have enabled 
DVMRP.

Command Mode 

Normal Exec, Privileged Exec

Example

Console#show ip dvmrp neighbor

Address

Interface

Uptime

Expire

Capabilities

---------------- --------------- -------- -------- -------------

10.1.0.254

vlan1

79315

32

6

Console#

Table 4-108   show ip dvmrp neighbor - display description

Field

Description

Address

The IP address of the network device immediately upstream for this multicast delivery 

tree.

Interface

The IP interface on this router that connects to the upstream neighbor.

Uptime

The time since this device last became a DVMRP neighbor.

Expire

The time remaining before this entry will be aged out.

Capabilities

The neighboring router’s capabilities may include:
Leaf (bit 0) - 

Neighbor has only one interface with neighbors. 

Prune (bit 1) - 

Neighbor supports pruning. 

Generation ID (bit 2) -  Neighbor sends its Generation ID in probe messages. 

Mtrace (bit 3) - 

Neighbor can handle multicast trace requests.

SNMP (bit 4) - 

Neighbor is SNMP capable.

Netmask - (bit 5) - 

Neighbor will accept network masks appended to the prune, 

graft, and graft acknowledgement messages.

Reserved (bit 6 and 7) -  Reserved for future use.

Console#show ip dvmrp interface
Vlan 1 is up

DVMRP is enabled
Metric is 1

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов