manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 640 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 640

Command Line Interface

4-312

4

Command Usage 

The multicast interface that first receives a multicast stream from a particular 
source forwards this traffic to all other PIM interfaces on the router. If there are 
no requesting groups on that interface, the leaf node sends a prune message 
upstream and enters a prune state for this multicast stream. The prune state is 
maintained until the join-prune-holdtime timer expires or a graft message is 
received for the forwarding entry. 

Example

ip pim graft-retry-interval

This command configures the time to wait for a Graft acknowledgement before 
resending a Graft. Use the 

no

 form to restore the default value.

Syntax 

ip pim graft-retry-interval 

seconds

no ip pim graft-retry-interval

seconds

 - The time before resending a Graft. (Range: 0-65535)

Default Setting 

3 seconds

Command Mode 

Interface Configuration (VLAN)

Command Usage 

A graft message is sent by a router to cancel a prune state. When a router 
receives a graft message, it must respond with an graft acknowledgement 
message. If this acknowledgement message is lost, the router that sent the 
graft message will resend it a number of times (as defined by the 

ip pim 

max-graft-retries

 command). 

Example

ip pim max-graft-retries

This command configures the maximum number of times to resend a Graft message 
if it has not been acknowledged. Use the 

no

 form to restore the default value.

Syntax 

ip pim max-graft-retries 

retries

no ip pim graft-retry-interval

retries

 - The maximum number of times to resend a Graft. 

(Range: 0-65535)

Console(config-if)#ip pim join-prune-holdtime 60
Console(config-if)#

Console(config-if)#ip pim graft-retry-interval 9
Console(config-if)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов