manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 631 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 631

Multicast Routing Commands

4-303

4

default-gateway

This command specifies the default DVMRP gateway for IP multicast traffic. Use the 

no

 form to remove the default gateway.

Syntax 

default-gateway 

ip-address

no default-gateway

ip-address

 - IP address of the default DVMRP gateway.

Default Setting 

None

Command Mode 

Router Configuration

Command Usage 

• The specified interface advertises itself as a default route to neighboring 

DVMRP routers. It advertises the default route out through its other interfaces. 
Neighboring routers on the other interfaces return Poison Reverse messages 
for the default route back to the router. When the router receives these 
messages, it records all the downstream routers for the default route.

• When multicast traffic with an unknown source address (i.e., not found in the 

route table) is received on the default upstream route interface, the router 
forwards this traffic out through the other interfaces (with known downstream 
routers). However, when multicast traffic with an unknown source address is 
received on another interface, the router drops it because only the default 
upstream interface can forward multicast traffic from an unknown source.

Example

ip dvmrp

This command enables DVMRP on the specified interface. Use the 

no

 form to 

disable DVMRP on this interface.

Syntax 

ip dvmrp
no ip dvmrp

Default Setting 

Disabled

Command Mode 

Interface Configuration (VLAN)

Console(config-router)#default-gateway 10.1.0.253
Console(config-router)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов