Edge-Core ES4625 Скачать руководство пользователя страница 62

Страница: 62 / 674

Configuring the Switch

3-10

Routing Protocol

3-206

RIP

3-224

General Settings

Enables or disables RIP, sets the global RIP version and timer

values

3-225

Network Addresses

Configures the network interfaces that will use RIP

3-227

Interface Settings

Configures RIP parameters for each interface, including send

and receive versions, message loopback prevention, and

authentication

3-228

Statistics

Displays general information on update time, route changes and

number of queries, as well as a list of statistics for known

interfaces and neighbors

3-231

OSPF

3-234

General Configuration

Enables or disables OSPF; also configures the Router ID and

various other global settings

3-235

Area Configuration

Specifies rules for importing routes into each area

3-238

Area Range Configuration Configures route summaries to advertise at an area boundary

3-241

Interface Configuration

Shows area ID and designated router; also configures OSPF

protocol settings and authentication for each interface

3-243

Virtual Link Configuration

Configures a virtual link through a transit area to the backbone

3-247

Network Area Address

Configuration

Defines OSPF areas and associated interfaces

3-249

Summary Address

Configuration

Aggregates routes learned from other protocols for advertising

into other autonomous systems

3-252

Redistribute Configuration Redistributes routes from one routing domain to another

3-253

NSSA Settings

Configures settings for importing routes into or exporting routes

out of not-so-stubby areas

3-254

Link State Database

Information

Shows information about different OSPF Link State

Advertisements (LSAs) stored in this router’s database

3-256

Border Router Information Displays routing table entries for area border routers and

autonomous system boundary routers

3-258

Neighbor Information

Displays information about neighboring routers on each

interface within an OSPF area

3-259

DVMRP

3-264

General Settings

Configure global settings for prune and graft messages, and the

exchange of routing information

3-264

Interface Settings

Enables/disables DVMRP per interface and sets the route metric

3-267

Neighbor Information

Displays neighboring DVMRP routers

3-269

Routing Table

Displays DVMRP routing information

3-270

Table 3-2 Switch Main Menu

(Continued)

Description

Page

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 62 / 674

Результаты поиска

Содержание ES4625

Отзывы: