Edge-Core ES4625 Скачать руководство пользователя страница 651

Страница: 651 / 674

Router Redundancy Commands

4-323

clear vrrp router counters

This command clears VRRP system statistics.

Command Mode

Privileged Exec

Example

clear vrrp interface counters

This command clears VRRP system statistics for the specified group and interface.

clear vrrp

group

interface

interface

counters

•

group

- Identifies a VRRP group. (Range: 1-255)

•

interface

- Identifier of configured VLAN interface. (Range: 1-4093)

Defaults

None

Command Mode

Privileged Exec

Example

Console#clear vrrp router counters
Console#

Console#clear vrrp 1 interface 1 counters
Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 651 / 674

Результаты поиска

Содержание ES4625

Отзывы: