manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 456 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 456

Command Line Interface

4-128

4

Command Mode

DHCP Pool Configuration

Usage Guidelines 

The IP address of the router should be on the same subnet as the client. You 
can specify up to two routers. Routers are listed in order of preference 
(starting with 

address1

 as the most preferred router).

Example 

domain-name

This command specifies the domain name for a DHCP client. Use the 

no

 form to 

remove the domain name.

Syntax 

domain-name

 

domain

no domain-name

domain

 - Specifies the domain name of the client. 

(Range: 1-32 characters)

Default Setting 

None

Command Mode

DHCP Pool Configuration

Example 

dns-server

This command specifies the Domain Name System (DNS) IP servers available to a 
DHCP client. Use the 

no

 form to remove the DNS server list.

Syntax

dns-server

 

address1

 [

address2

]

no dns-server

•

address1

 - Specifies the IP address of the primary DNS server.

•

address2

 - Specifies the IP address of the alternate DNS server.

Default Setting 

None

Command Mode

DHCP Pool Configuration

Console(config-dhcp)#default-router 10.1.0.54 10.1.0.64
Console(config-dhcp)#

Console(config-dhcp)#domain-name sample.com
Console(config-dhcp)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов