Edge-Core ES4625 Скачать руководство пользователя страница 544

Страница: 544 / 674

Command Line Interface

4-216

Default Setting

None

Command Mode

Privileged Exec

Example

The following shows that HTTP traffic has been mapped to CoS value 0:

Related Commands

map ip port (Global Configuration) (4-211)
map ip port (Interface Configuration) (4-212)

show map ip precedence

This command shows the IP precedence priority map.

Syntax

show map ip precedence

[

interface

]

interface

•

ethernet

unit

port

unit

- Stack unit. (Range: 1-8)

port

- Port number. (Range: 1-25/49)

•

port-channel

channel-id

(Range: 1-32)

Default Setting

None

Command Mode

Privileged Exec

Console#show map ip port
TCP port mapping status: disabled

Port

Port no. COS

--------- -------- ---

Eth 1/ 5

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 544 / 674

Результаты поиска

Содержание ES4625

Отзывы: