Edge-Core ES4625 Скачать руководство пользователя страница 639 | Manualshive

Страница: 639 / 674

Edge-Core ES4625 Скачать руководство пользователя страница 639

Multicast Routing Commands

4-311

4

ip pim trigger-hello-interval

This command configures the maximum time before transmitting a triggered PIM
Hello message after the router is rebooted or PIM is enabled on an interface. Use
the

no

form to restore the default value.

Syntax

ip pim triggerr-hello-interval

seconds

no ip pim triggerr-hello-interval

seconds

- The maximum time before sending a triggered PIM Hello

message. (Range: 0-65535)

Default Setting

5 seconds

Command Mode

Interface Configuration (VLAN)

Command Usage

• When a router first starts or PIM is enabled on an interface, the hello-interval

is set to random value between 0 and the trigger-hello-interval. This prevents
synchronization of Hello messages on multi-access links if multiple routers are
powered on simultaneously.

• Also, if a Hello message is received from a new neighbor, the receiving router

will send its own Hello message after a random delay between 0 and the
trigger-hello-interval.

Example

ip pim join-prune-holdtime

This command configures of the hold time for the prune state. Use the

no

form to

restore the default value.

Syntax

ip pim join-prune-holdtime

seconds

no ip pim join-prune-holdtime

seconds

- The hold time for the prune state. (Range: 0-65535)

Default Setting

210 seconds

Command Mode

Interface Configuration (VLAN)

Console(config-if)#ip pim triggerr-hello-interval 10
Console(config-if)#

«
...
637
638
639
640
641
...
»

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов