Edge-Core ES4625 Скачать руководство пользователя страница 558

Страница: 558 / 674

Command Line Interface

4-230

IGMP Query Commands

(Layer 2)

ip igmp snooping querier

This command enables the switch as an IGMP querier. Use the

form to disable it.

Syntax

[

]

ip igmp snooping querier

Default Setting

Enabled

Command Mode

Global Configuration

Command Usage

If enabled, the switch will serve as querier if elected. The querier is
responsible for asking hosts if they want to receive multicast traffic.

Example

ip igmp snooping query-count

This command configures the query count. Use the

form to restore the default.

Syntax

ip igmp snooping query-count

count

no ip igmp snooping query-count

count

- The maximum number of queries issued for which there has been

no response before the switch takes action to drop a client from the
multicast group. (Range: 2-10)

Default Setting

2 times

Table 4-75 IGMP Query Commands (Layer 2)

Command

Function

Mode

Page

ip igmp snooping querier

Allows this device to act as the querier for IGMP snooping GC

4-230

ip igmp snooping

query-count

Configures the query count

4-230

ip igmp snooping

query-interval

Configures the query interval

4-231

ip igmp snooping

query-max-response-time

Configures the report delay

4-231

ip igmp snooping

router-port-expire-time

Configures the query timeout

4-232

Console(config)#ip igmp snooping querier
Console(config)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 558 / 674

Результаты поиска

Содержание ES4625

Отзывы: