Edge-Core ES4625 Скачать руководство пользователя страница 453

Страница: 453 / 674

DHCP Commands

4-125

service dhcp

This command enables the DHCP server on this switch. Use the

form to disable

the DHCP server.

Syntax

[

]

service dhcp

Default Setting

Enabled

Command Mode

Global Configuration

Command Usage

If the DHCP server is running, you must restart it to implement any
configuration changes.

Example

ip dhcp excluded-address

This command specifies IP addresses that the DHCP server should not assign to
DHCP clients. Use the

form to remove the excluded IP addresses.

Syntax

[

]

ip dhcp excluded-address

low-address

[

high-address

]

•

low-address

- An excluded IP address, or the first IP address in an excluded

address range.

•

high-address

- The last IP address in an excluded address range.

netbios-node-type

Configures NetBIOS node type for Microsoft DHCP clients

4-131

lease

Sets the duration an IP address is assigned to a DHCP client

4-131

host

Specifies the IP address and network mask to manually bind to a

DHCP client

4-132

client-identifier

Specifies a client identifier for a DHCP client

4-133

hardware-address

Specifies the hardware address of a DHCP client

4-134

clear ip dhcp binding

Deletes an automatic address binding from the DHCP server

database

4-134

show ip dhcp binding

Displays address bindings on the DHCP server

PE,

4-135

* These commands are used for manually binding an address to a client.

Console(config)#service dhcp
Console(config)#

Table 4-45 DHCP Server Commands

(Continued)

Command

Function

Mode Page

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES4625

Отзывы:

Edge-Core ES4625, Руководство по управлению, Страница: 453 / 674

Результаты поиска

Содержание ES4625

Отзывы: