manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 193 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 193

VLAN Configuration

3-141

3

Web

 – Click VLAN, 802.1Q VLAN, Static List. To create a new VLAN, enter the 

VLAN ID and VLAN name, mark the Enable checkbox to activate the VLAN, and 
then click Add.

Figure 3-78   VLAN Static List - Creating VLANs

CLI

 – This example creates a new VLAN.

Adding Static Members to VLANs 

(VLAN Index)

Use the VLAN Static Table to configure port members for the selected VLAN index. 
Assign ports as tagged if they are connected to 802.1Q VLAN compliant devices, or 
untagged they are not connected to any VLAN-aware devices. Or configure a port 
as forbidden to prevent the switch from automatically adding it to a VLAN via the 
GVRP protocol.

Notes: 1.

You can also use the VLAN Static Membership by Port page to configure 
VLAN groups based on the port index (page 3-143). However, note that this 
configuration page can only add ports to a VLAN as tagged members.

2.

VLAN 1 is the default untagged VLAN containing all ports on the switch, and 
can only be modified by first reassigning the default port VLAN ID as 
described under “Configuring VLAN Behavior for Interfaces” on page 3-144.

Console(config)#vlan database

4-189

Console(config-vlan)#vlan 2 name R&D media ethernet state active

4-189

Console(config-vlan)#end
Console#show vlan

4-196

VLAN ID:

1

Type:

Static

Name:

DefaultVlan

Status:

Active

Ports/Port Channels:

Eth1/ 1(S) Eth1/ 2(S) Eth1/ 3(S) Eth1/ 4(S) Eth1/ 5(S)
Eth1/ 6(S) Eth1/ 7(S) Eth1/ 8(S) Eth1/ 9(S) Eth1/10(S)
Eth1/11(S) Eth1/12(S) Eth1/13(S) Eth1/14(S) Eth1/15(S)
Eth1/16(S) Eth1/17(S) Eth1/18(S) Eth1/19(S) Eth1/20(S)
Eth1/21(S) Eth1/22(S) Eth1/23(S) Eth1/24(S)

.

.

.
VLAN ID:

2

Type:

Static

Name:

R&D

Status:

Active

Ports/Port Channels:

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов