manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 421 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 421

Access Control List Commands

4-93

4

Related Commands

access-list ip (4-89)

show ip access-list 

This command displays the rules for configured IP ACLs.

Syntax

show ip access-list 

{

standard 

| 

extended

} [

acl_name

]

•

standard

 – Specifies a standard IP ACL.

•

extended

 – Specifies an extended IP ACL.

•

acl_name

 – Name of the ACL. (Maximum length: 16 characters)

Command Mode

Privileged Exec

Example 

Related Commands

permit, deny 4-90
ip access-group (4-98)

access-list ip mask-precedence 

This command changes to the IP Mask mode used to configure access control 
masks. Use the 

no

 form to delete the mask table.

Syntax

[

no

]

 access-list ip mask-precedence 

{

in 

| 

out

}

•

in

 – Ingress mask for ingress ACLs.

•

out

 – Egress mask for egress ACLs.

Default Setting

Default system mask: Filter inbound packets according to specified IP ACLs.

Command Mode

Global Configuration

Command Usage

• A mask can only be used by all ingress ACLs or all egress ACLs.
• The precedence of the ACL rules applied to a packet is not determined by 

order of the rules, but instead by the order of the masks; i.e., the first mask 
that matches a rule will determine the rule that is applied to a packet.

Console#show ip access-list standard
IP standard access-list david:

permit host 10.1.1.21
permit 168.92.0.0 255.255.15.0

Console#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов