manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 506 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 506

Command Line Interface

4-178

4

Default Setting 

Switch’s MAC address

Command Mode 

MST Configuration

Command Usage 

The MST region name and revision number (page 4-178) are used to 
designate a unique MST region. A bridge (i.e., spanning-tree compliant device 
such as this switch) can only belong to one MST region. And all bridges in the 
same region must be configured with the same MST instances.

Example 

Related Commands

revision (4-178)

revision

This command configures the revision number for this multiple spanning tree 
configuration of this switch. Use the 

no

 form to restore the default.

Syntax 

revision

 

number

number

 - Revision number of the spanning tree. (Range: 0-65535)

Default Setting 

0

Command Mode 

MST Configuration

Command Usage 

The MST region name (page 4-177) and revision number are used to 
designate a unique MST region. A bridge (i.e., spanning-tree compliant device 
such as this switch) can only belong to one MST region. And all bridges in the 
same region must be configured with the same MST instances.

Example 

Related Commands

name (4-177)

Console(config-mstp)#name R&D
Console(config-mstp)#

Console(config-mstp)#revision 1
Console(config-mstp)#

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов