manualshive.com logo in svg

Edge-Core ES4625, Руководство по управлению, Страница: 376 / 674

Поделиться
Скачать
Edge-Core ES4625 Скачать руководство пользователя страница 376

Command Line Interface

4-48

4

Example

The following example shows that system logging is enabled, the message level for 
flash memory is “errors” (i.e., default level 3 - 0), and the message level for RAM is 
“debugging” (i.e., default level 7 - 0). 

The following example displays settings for the trap function. 

Related Commands

show logging sendmail (4-52)

Console#show logging flash
Syslog logging:

Enabled

History logging in FLASH: level errors
Console#show logging ram
Syslog logging:

Enabled

History logging in RAM: level debugging
Console#

Table 4-19   show logging flash/ram - display description

Field

Description

Syslog logging

Shows if system logging has been enabled via the 

logging on

 command.

History logging in FLASH The message level(s) reported based on the 

logging history

 command.

History logging in RAM

The message level(s) reported based on the 

logging history

 command.

Console#show logging trap
Syslog logging: Enable
REMOTELOG status: disable
REMOTELOG facility type: local use 7
REMOTELOG level type:

Debugging messages

REMOTELOG server IP address: 1.2.3.4
REMOTELOG server IP address: 0.0.0.0
REMOTELOG server IP address: 0.0.0.0
REMOTELOG server IP address: 0.0.0.0
REMOTELOG server IP address: 0.0.0.0
Console#

Table 4-20   show logging trap - display description

Field

Description

Syslog logging

Shows if system logging has been enabled via the 

logging on

 command.

REMOTELOG status

Shows if remote logging has been enabled via the 

logging trap

 command.

REMOTELOG 

facility type

The facility type for remote logging of syslog messages as specified in the 

logging facility

 command.

REMOTELOG level type The severity threshold for syslog messages sent to a remote server as specified 

in the 

logging trap

 command.

REMOTELOG 

server IP address

The address of syslog servers as specified in the 

logging host

 command.

Содержание ES4625



































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов